機箱機柜如何安裝雖然不難，但仍然有一些細節問題需要了解，平時也有不少朋友多次問到一些細節事項，下面一起來了解下吧。

Although it is not difficult to install the chassis and cabinet, there are still some details that need to be understood. Usually, many friends have asked for some details many times. Let's take a look.

1、有了濟南機箱機柜相關尺寸，再檢查設備的外形，確保和選擇的支架搭配。一個堅固的機柜可承重達250公斤，所有安裝螺絲不得有松動，保護橡皮墊應安裝牢固，所以檢查一下用來拿出設備用的工具，比如，提門或手推車。好的機柜下面裝有輪子，所以你只需把該裝的設備裝進去，再把機柜推到合適的地方即可。

1. With the relevant dimensions of Jinan chassis and cabinet, check the appearance of the equipment to ensure that it matches the selected bracket. A sturdy cabinet can bear a weight of up to 250 kilograms, all mounting screws must not be loose, and protective rubber pads should be securely installed, so check the tools used to take out the equipment, such as a door lift or a trolley. A good cabinet has wheels under it, so you just need to install the equipment that needs to be installed and then push the cabinet to the appropriate location.

2、測量一下房間的大小和機柜經過的天花板、門和電梯高度。再有，考慮到機柜里的多類設備，確保把機柜放在距離電源、網線插口、通訊插口近的地方。

2. Measure the size of the room and the height of the ceiling, door, and elevator through which the cabinet passes. Moreover, considering the multiple types of equipment in the cabinet, ensure that the cabinet is placed close to the power supply, network cable jack, and communication jack.

3、檢查打開和關閉機柜時柜門打開的角度及，標準機柜門在右邊打開，門軸在左邊，當然不排除相反的情況。所有的門和側板都應很容易打開，以便于維護。安放應豎直，柜面保持水平，垂直偏差小于等于百分之一，水平偏差小于等于3mm，機柜之間縫隙小于等于1mm，機柜表面要完整，無損傷，螺絲要堅固，每表面凹凸度應小于1mm。

3. Check the angle at which the cabinet door opens when opening and closing the cabinet. The standard cabinet door opens on the right and the door shaft is on the left. Of course, the opposite is not ruled out. All doors and side panels should be easily opened for maintenance purposes. The installation should be vertical, the cabinet surface should be kept horizontal, with a vertical deviation of less than or equal to 1%, a horizontal deviation of less than or equal to 3mm, and a gap between cabinets of less than or equal to 1mm. The cabinet surface should be complete and undamaged, the screws should be firm, and the surface roughness per square meter should be less than 1mm.

4、當你要將設備機柜安裝入一個已經存在的機柜組時，你可以把機柜挨著排成一排，這樣、整齊。有些機柜組由于種種原因，不能再增加了，或者只能增加幾種附件。好的機柜組模型應具有充分的可擴充性，并帶有所有必要的硬件，可把機柜側板拿掉，用螺釘將機柜相互連接，排成一排。

4. When installing equipment cabinets into an existing cabinet group, you can arrange the cabinets in a row next to each other, so that they are safe and tidy. Some cabinet groups cannot be added anymore due to various reasons, or only a few accessories can be added. A good cabinet group model should have sufficient scalability and include all necessary hardware. The cabinet side panels can be removed, and the cabinets can be connected to each other with screws to form a row.

機箱機柜安裝細節相關內容就講解到這里了，您對此有怎樣的疑惑或者需求，就來我們網站http://nmnewnet.cn進行咨詢了解吧！

That's all about the installation details of the chassis and cabinet. If you have any doubts or needs about this, please come to our website http://nmnewnet.cn Get to know through consultation!